AutoCAD Takes a Long Time to Start Plotting
After clicking Plot, AutoCAD waits a long time before the job begins or reaches the output device. Start by identifying exactly where the problem first appears, then test the most likely causes one at a time. This avoids changing a correct drawing to compensate for a PDF, driver or printer problem.
Symptoms — confirm exactly what is wrong
- After clicking Plot, AutoCAD waits a long time before the job begins or reaches the output device.
- Check whether the failure happens with one DWG/one sheet or with every drawing.
- Test the same sheet to a local AutoCAD PDF PC3; this quickly separates drawing content from a physical/network device.
Beginner rule: Change one setting at a time. After each change, repeat the same test so you know what actually fixed the problem.
30-second triage: Run a small foreground test with BACKGROUNDPLOT = 0. If a simple drawing plots but the project drawing fails, focus on drawing content. If every drawing fails to one device, focus on PC3/driver/environment.
Likely causes — check these in order
| Likely cause | Why it creates this symptom | Quick check |
|---|---|---|
| Drawing is unusually large or complex | Dense xrefs, hatches, images, viewports or corruption can make plotting slow or unstable. | Test a copy with AUDIT/PURGE where appropriate and publish a simpler Layout for comparison. |
| Printer/driver interrogation is slow | Opening Plot can wait on unavailable network printers, stale PC3s or slow drivers. | Temporarily switch to a known-good local PDF PC3 and compare Plot dialog speed. |
| Network printer/plotter path is unavailable | The printer queue, UNC path or server may be offline or unreachable. | Test the same device from Windows and verify network/server availability. |
| Background plotting/publishing interaction | Background processing can hide the first failing sheet or interact with unstable resources. | Set BACKGROUNDPLOT to 0 for a controlled foreground test. |
| PDF PC3/preset differs | A different PDF preset can change quality, fonts, layers and other output behavior. | Compare the current PDF PC3 with the known-good project preset. |
For the underlying setup behind these checks, use AutoCAD Background Publishing Explained and AutoCAD PDF Is Slow to Open or Print: What to Check while you diagnose the symptom.
Diagnostic path — isolate the responsible setting
Work through the checks in order. Do not apply a fix until its diagnostic check differs from the known-good project standard.
Diagnostic 1 — Drawing is unusually large or complex
Where: The failing DWG/Layout; compare with a simple drawing and a copy used for diagnostic isolation.
Do this: Test a copy with AUDIT/PURGE where appropriate and publish a simpler Layout for comparison.
Check: If this differs from the known-good project standard, correct it and retest before continuing.
Diagnostic 2 — Printer/driver interrogation is slow
Where: PAGESETUP/PLOTTERMANAGER; compare the affected device with a local AutoCAD PDF PC3.
Do this: Temporarily switch to a known-good local PDF PC3 and compare Plot dialog speed.
Check: If this differs from the known-good project standard, correct it and retest before continuing.
Diagnostic 3 — Network printer/plotter path is unavailable
Where: Windows printer queue/network connection, then AutoCAD.
Do this: Test the same device from Windows and verify network/server availability.
Check: If this differs from the known-good project standard, correct it and retest before continuing.
Diagnostic 4 — Background plotting/publishing interaction
Where: Command line > BACKGROUNDPLOT, or Options > Plot and Publish > Background Processing.
Do this: Set BACKGROUNDPLOT to 0 for a controlled foreground test.
Check: If this differs from the known-good project standard, correct it and retest before continuing.
Diagnostic 5 — PDF PC3/preset differs
Where: PAGESETUP > Modify.
Do this: Compare the current PDF PC3 with the known-good project preset.
Check: If this also matches the known-good setup, use the isolation test below instead of changing unrelated settings.
Fixes — use only the fix that matches your diagnosis
Fix 1 — Reduce drawing-specific plotting load
Use this fix when: your diagnosis confirmed that Drawing is unusually large or complex.
Do this: Test a copy with problematic xrefs/images/hatches isolated. Repair drawing issues and simplify only the content that is proven to cause the delay.
Check: Retest the same failing action with the simplest known-good output path before applying another change.
Fix 2 — Remove the slow device dependency
Use this fix when: your diagnosis confirmed that Printer/driver interrogation is slow.
Do this: Test with a local AutoCAD PDF PC3. If Plot opens normally, repair/remove the unavailable printer, stale PC3 or slow network driver.
Check: Retest the same failing action with the simplest known-good output path before applying another change.
Fix 3 — Restore the network queue/path
Use this fix when: your diagnosis confirmed that Network printer/plotter path is unavailable.
Do this: Bring the server/queue online, reconnect the Windows printer, then reopen AutoCAD and test a simple PDF/physical plot.
Check: Retest the same failing action with the simplest known-good output path before applying another change.
Fix 4 — Retest in the foreground
Use this fix when: your diagnosis confirmed that Background plotting/publishing interaction.
Do this: Set BACKGROUNDPLOT = 0 and run a small controlled Plot/PUBLISH job. Re-enable background only after the cause is understood.
Check: Retest the same failing action with the simplest known-good output path before applying another change.
Fix 5 — Return to the approved PDF preset
Use this fix when: your diagnosis confirmed that PDF PC3/preset differs.
Do this: Select the known-good project PDF PC3 and its PDF options. Compare the same Layout before changing drawing content.
Check: Retest the same failing action with the simplest known-good output path before applying another change.
Verification — prove the fix before full production
- Retest the simplest known-good drawing through a local AutoCAD PDF PC3.
- Retest the original failing Layout with the single confirmed fix applied.
- For PUBLISH, run a 2–3 sheet subset containing the former failing sheet.
- Only after that succeeds should you run the complete production batch.
Still not fixed? Use an isolation test
Test a simple DWG to the affected device and the failing DWG to a local PDF PC3. This comparison separates drawing content from PC3/driver/environment causes.
Prevention — reduce the chance of recurrence
- Keep AutoCAD, printer drivers and approved PC3/CTB/STB files under controlled update procedures.
- Use small publish subsets to diagnose a failing sheet instead of rerunning the entire package.
- Keep a local AutoCAD PDF PC3 as the baseline output path.
- Archive publish details/logs when a production batch fails so the next diagnosis starts with evidence.
Official Autodesk references
Use these references when the interface, driver or plot-style behavior on your workstation differs from the checks above.
Frequently asked questions
What should I check first?
Start with Drawing is unusually large or complex. Use the quick check in the diagnostic section before changing anything else.
What if that check is correct?
Move to Printer/driver interrogation is slow. The goal is to eliminate causes one at a time, not to change several settings together.
Should I keep retrying the full batch after a crash or hang?
No. Isolate the failing drawing, sheet or output device with a small controlled test first.
Explore more in CAD Printing & Plotting Troubleshooting.