Right Side of AutoCAD Plot Is Cut Off
The right border or right-side drawing content is clipped while the rest of the sheet appears normal. Start by identifying exactly where the problem first appears, then test the most likely causes one at a time. This avoids changing a correct drawing to compensate for a PDF, driver or printer problem.
Symptoms — confirm exactly what is wrong
- The right border or right-side drawing content is clipped while the rest of the sheet appears normal.
- Note exactly which edge is missing or which direction the plot has shifted.
- Compare Plot Preview, the saved PDF and the physical sheet; clipping may begin at only one of those stages.
Beginner rule: Change one setting at a time. After each change, repeat the same test so you know what actually fixed the problem.
30-second triage: If the border is already cut in Plot Preview, fix AutoCAD’s paper, Plot Area, offset or printable area. If Preview and PDF are complete but paper is cut, troubleshoot the physical device/driver instead.
Likely causes — check these in order
| Likely cause | Why it creates this symptom | Quick check |
|---|---|---|
| Printable area is smaller than expected | The device cannot mark all the way to the nominal paper edge. | Compare the border with the dashed printable boundary in the Layout. |
| Wrong paper size | A near-size sheet can force resizing or clipping. | Compare the exact paper dimensions with the title block. |
| Plot offset is wrong | X/Y plot offsets move the plotted area relative to the printable area or paper edge. | Open Plot/Page Setup and read Plot Offset X and Y. |
| Drawing orientation is wrong | Portrait, Landscape or upside-down output does not match the sheet. | Check Drawing Orientation in PAGESETUP. |
| Wrong Plot Area | Window, Extents, Display or another area is being plotted instead of the intended Layout. | Open PAGESETUP > Plot Area and verify the intended selection. |
For the underlying setup behind these checks, use AutoCAD Border Cut Off When Plotting: Causes and Fixes and AutoCAD Printable Area and Plot Margins Explained while you diagnose the symptom.
Diagnostic path — isolate the responsible setting
Work through the checks in order. Do not apply a fix until its diagnostic check differs from the known-good project standard.
Diagnostic 1 — Printable area is smaller than expected
Where: PAGESETUP > Modify.
Do this: Compare the border with the dashed printable boundary in the Layout.
Check: If this differs from the known-good project standard, correct it and retest before continuing.
Diagnostic 2 — Wrong paper size
Where: PAGESETUP > Modify.
Do this: Compare the exact paper dimensions with the title block.
Check: If this differs from the known-good project standard, correct it and retest before continuing.
Diagnostic 3 — Plot offset is wrong
Where: PAGESETUP > Modify.
Do this: Open Plot/Page Setup and read Plot Offset X and Y.
Check: If this differs from the known-good project standard, correct it and retest before continuing.
Diagnostic 4 — Drawing orientation is wrong
Where: PAGESETUP > Modify.
Do this: Check Drawing Orientation in PAGESETUP.
Check: If this differs from the known-good project standard, correct it and retest before continuing.
Diagnostic 5 — Wrong Plot Area
Where: PAGESETUP > Modify.
Do this: Open PAGESETUP > Plot Area and verify the intended selection.
Check: If this also matches the known-good setup, use the isolation test below instead of changing unrelated settings.
Fixes — use only the fix that matches your diagnosis
Fix 1 — Move critical border content inside the printable area
Use this fix when: your diagnosis confirmed that Printable area is smaller than expected.
Do this: Use the dashed printable boundary for the actual device. If the border standard requires more area, use a device/media configuration that supports it.
Check: Run Preview and inspect all four border edges before changing another setting.
Fix 2 — Use the exact project paper
Use this fix when: your diagnosis confirmed that Wrong paper size.
Do this: Select the exact ISO/ANSI/ARCH or approved custom media that matches the title block.
Check: Run Preview and inspect all four border edges before changing another setting.
Fix 3 — Reset or intentionally set Plot Offset
Use this fix when: your diagnosis confirmed that Plot offset is wrong.
Do this: For Window/Extents plots, use Center the Plot or enter the documented X/Y offset. For Layout plotting, correct the Layout/Page Setup instead of using arbitrary offsets.
Check: Run Preview and inspect all four border edges before changing another setting.
Fix 4 — Correct Drawing Orientation
Use this fix when: your diagnosis confirmed that Drawing orientation is wrong.
Do this: Open PAGESETUP > Drawing Orientation and select Portrait or Landscape to match the title block.
Check: Run Preview and inspect all four border edges before changing another setting.
Fix 5 — Choose the intended Plot Area
Use this fix when: your diagnosis confirmed that Wrong Plot Area.
Do this: For a production Layout choose Layout. For a deliberate Window/Extents workflow, redefine the intended area and Preview it.
Check: Run Preview and inspect all four border edges before changing another setting.
Verification — prove the fix before full production
- Preview the entire border at the corrected paper size and orientation.
- Create a PDF and confirm all four border edges are present.
- Check the PDF page dimensions against the title block standard.
- If hardcopy matters, plot one physical test and inspect every edge before the full set.
Still not fixed? Use an isolation test
Create one PDF from the same Page Setup. If the PDF border is complete but paper is not, stop editing the DWG and test the physical printer/driver.
Prevention — reduce the chance of recurrence
- Design borders around the approved device’s printable area, not just the nominal paper edge.
- Keep paper size, orientation and Plot Area in named Page Setups.
- Use documented offsets only for workflows that genuinely require Window/Extents positioning.
- Retest borders after printer-driver, PC3 or custom-media changes.
Official Autodesk references
Use these references when the interface, driver or plot-style behavior on your workstation differs from the checks above.
Frequently asked questions
What should I check first?
Start with Printable area is smaller than expected. Use the quick check in the diagnostic section before changing anything else.
What if that check is correct?
Move to Wrong paper size. The goal is to eliminate causes one at a time, not to change several settings together.
Should I shrink the whole sheet to stop clipping?
Not for a production Layout. Correct the paper, printable area, Plot Area or offset that caused the clipping.
Explore more in CAD Printing & Plotting Troubleshooting.